精品综合久久久久久97_亚洲国产精品久久久久婷婷老年_成人区人妻精品一区二区三区_国产精品JIZZ在线观看老狼_国产欧美精品一区二区三区

產品詳情：

OMC系列·無動力氣流分級機
OMC Series · Unpowered Air Flow Classifier
工作原理：
物料被定量加入到主機上方腔體內，在導流環的作用下被初步分散，在沿筒壁下落的過程中，又收到從下方補風口中進入的二次氣流的進一步打散，該打散效果受到風量的影響，使用時可以通過調節分散環與筒壁的相對上下位置來調節，進而影響分選的精度，較細的顆粒會在上升氣流的作用下向中心匯聚，并*終從*上方的出料口中離開，通過管道進入后道收塵設備（旋風分離器、布袋除塵器等），較粗的顆粒將繼續沿筒壁而下，從*下端被卸出。
working principle:
The material is quantitatively added into the cavity above the main unit, and is initially dispersed under the action of the deflector ring. In the process of falling along the wall of the cylinder, it is further dispersed by the secondary air flow entering from the supplementary air inlet below. The scattering effect is affected by the air volume. When using it, it can be adjusted by adjusting the relative up and down positions of the dispersing ring and the cylinder wall, thereby affecting the accuracy of sorting. The finer particles will converge toward the center under the action of the upward airflow, and eventually leave from the top discharge port, it enters the downstream dust collection equipment (cyclone separator, bag dust collector, etc.) through the pipeline, and the coarser particles will continue to go down the cylinder wall and be discharged from the lowermost end.
 
設備特點：

1.   主機不需要任何動件，因此能耗低，后期維護成本低廉，并且處理量相對較大。

2.   通過調節分散環位置即可調節出料粒度，操作簡單。

3.   適用于為去除原料中的過細粉而產能要求又較高的物料分級。

4.  

1. The main unit does not need any moving parts, so the energy consumption is low, the maintenance cost in the later period is low, and the processing capacity is relatively large.
2. The particle size can be adjusted by adjusting the position of the dispersion ring, and the operation is simple.
3. It is suitable for the classification of materials with high production capacity requirements to remove the excessively fine powder in the raw materials.
 
技術參數表(Technical Data Sheet)：

注：具體配置及處理效果需根據物料性質與加工要求確認，可與我司工程師溝通或來料試驗。